The Sunny Plumber provides plumbing services throughout the Southwest United States. From basic plumbing repairs to top-of-the-line equipment installation, our Sunny Plumbers do it all. Our team is committed to providing your family with the cleanest water, most efficient systems, and freedom from the worry of plumbing problems in your home. We can’t wait to show you why they call us bright and shiny!
Pipefitters, sometimes simply called fitters, install and maintain pipes that carry chemicals, acids, and gases. These pipes are used mostly in manufacturing, commercial, and industrial settings. Fitters install and repair pipe systems in power plants, as well as heating and cooling systems in large office buildings. Some pipefitters specialize as gasfitters, sprinklerfitters, or steamfitters.
With over 20 years experience in Air Conditioning and Plumbing Repairs in the greater Las Vegas area, we will get the job done right the first time. We answer our telephones 24 hours a day and 7 days a week. Our technicians are Experienced, Drug Tested, Passed A Background Check, Licensed and Fully Trained. We give upfront Flat Rate pricing which means you pay by the job and not by the hour. All of our quotes are complete and presented to the client before work begins. The price you are quoted is the price you pay. No hidden fees or surprises!
PVC/CPVC – rigid plastic pipes similar to PVC drain pipes but with thicker walls to deal with municipal water pressure, introduced around 1970. PVC stands for polyvinyl chloride, and it has become a common replacement for metal piping. PVC should be used only for cold water, or for venting. CPVC can be used for hot and cold potable water supply. Connections are made with primers and solvent cements as required by code.[23]
Present-day water-supply systems use a network of high-pressure pumps, and pipes in buildings are now made of copper,[26] brass, plastic (particularly cross-linked polyethylene called PEX, which is estimated to be used in 60% of single-family homes[27]), or other nontoxic material. Due to its toxicity, most cities moved away from lead water-supply piping by the 1920s in the United States,[28] although lead pipes were approved by national plumbing codes into the 1980s,[29] and lead was used in plumbing solder for drinking water until it was banned in 1986.[28] Drain and vent lines are made of plastic, steel, cast-iron, or lead.[30][31]

Plumbers may not go out of their way to let you know that a toilet or sink can be moved. But if you’ve been working with them on a renovation, and they tell you something can’t be transferred to a new space, ask them to explain to you in detail why not. Speaking of things people don’t want to tell you, here are 10 things your neighbor isn’t being up-front about.
I have no problem paying for any service I receive but when Allied Reddi-Rooter came into my home and immediately tell me and them tell me it would cost me 350.00 for them to install a new Rheem water heater (his recommendation) that cost 409.00 I have a problem. If the cost is exactly how Home Advisor indicates then he’s charging 350.00an hour.  I did my homework checked with other plumbers and it. Would not take an hour to remove old and install the new water heater. Thank Goodness I did my research won’t be using their services and I will be letting others know what happen to me. Shame on you Allied

I think it is rather rude and a bit dishonest for people to not divulge their total fees upfront, an of course we should know to ask. But the normal person wouldn't know the questions to ask until they are burnt once like this, and then there still could be costs for walking up stairs or charge another service call if they need to go somewhere to use the bathroom and come back. THAT ISN'T A QUESTION I WOULD THINK TO ASK.


Need a quick fix? After having a plumber come out to your house, they might tell you the part needed to fix your toilet or sink issue is going to take a week. Don’t be too amenable if you can’t wait. There’s no shame in working with another plumber who can get the part and do the job when you need it. If you’re doing the job yourself, be sure you know these tips for completing a plumbing fix like a pro.
Nationally, the average water heater repair cost ranges between $120 and $200, although prices can range up to $400 or more. Water heater repair costs will depend on the type of water heater you have (tankless, electric, natural gas, etc.), the source of the problem, the cost for new parts, and labor rates in your area. Common water heater issues include problems with the thermocouple, thermostat, heating element and leaks. Most standard electric water heaters have two thermostats and two elements. One example for the cost to replace a bad thermostat is $185 for parts and labor. Replacing both the thermostat and the heating element could cost approximately $150-$200. The thermocouple is a safety device that senses when the pilot light is burning and signals the gas valve to close if the pilot light goes out. If your thermocouple is bad or corroded, the average cost to clean and repair it could be between $350 and $400. If your water heater has started to leak, it is usually more cost-effective to invest in a new water heater than to repair it, unless you’re covered by a warranty.
PBT – flexible (usually gray or black) plastic pipe which is attached to barbed fittings and secured in place with a copper crimp ring. The primary manufacturer of PBT tubing and fittings was driven into bankruptcy by a class-action lawsuit over failures of this system.[citation needed] However, PB and PBT tubing has since returned to the market and codes, typically first for "exposed locations" such as risers.

Homes have many combustion appliances, such as stoves, water heaters, fireplaces, furnaces, and boilers. Without proper ventilation, these appliances can create harmful gases such as carbon monoxide. Adequate ventilation is absolutely necessary in any home. For example, exhaust fans can play a pivotal role in clearing out harmful gases in bathrooms, cooking areas, and garages. They can keep the air clear of harmful moisture and fumes, while increasing your comfort by keeping humidity levels low.
Our master plumbers in Houston will assess the age and integrity of your pipes and determine the best course of action. Whether your home plumbing requires a pipe replacement, a horizontal pipe replacement for the pipes in your attic, or a whole-home repipe with highly durable and flexible PEX piping, you can rest easy knowing that your home is in the experienced hands of the licensed and highly-qualified John Moore Houston plumbing team.
Don’t flush floss, tampons, or even so-called “flushable” wipes. They don’t break down like toilet paper does and can come back to haunt you later. “Toilets are more water-efficient now than they were 20 years ago, so there sometimes isn’t enough volume in the flush to force debris down,” says Marcin Wroblewski, president of ExpressRooter Plumbing in Toronto. “An object will get lodged in the trap and cause blockage when waste builds up days later.”

Most plumbing training programs will include things such as coursework and on-the-job training. But, above and beyond what’s included you should expect other costs like books, tools, and uniforms which can range between a few hundred to a few thousand dollars. Depending on which program you choose, you may have to think about living expenses, as well.


Plumbing originated during ancient civilizations such as the Greek, Roman, Persian, Indian, and Chinese cities as they developed public baths and needed to provide potable water and wastewater removal, for larger numbers of people.[6] Standardized earthen plumbing pipes with broad flanges making use of asphalt for preventing leakages appeared in the urban settlements of the Indus Valley Civilization by 2700 BC.[7] The Romans used lead pipe inscriptions to prevent water theft. The word "plumber" dates from the Roman Empire.[8] The Latin for lead is plumbum. Roman roofs used lead in conduits and drain pipes[9] and some were also covered with lead. Lead was also used for piping and for making baths.[10]
The straight sections of plumbing systems are called "pipes" or "tubes". A pipe is typically formed via casting or welding, whereas a tube is made through extrusion. Pipe normally has thicker walls and may be threaded or welded, while tubing is thinner-walled and requires special joining techniques such as brazing, compression fitting, crimping, or for plastics, solvent welding. These joining techniques are discussed in more detail in the piping and plumbing fittings article.

We offer several financing options for new equipment, as well as our Priority Club Membership that grants members exclusive discounts, priority service, annual tune-ups, and much more. Plus, we make it our mission to give back to the community that’s continually supported us for decades. Our team members regularly donate their time, money, and efforts to numerous charitable organizations, fundraising endeavors, and worthwhile causes throughout the Northern Virginia and suburban Maryland area.
×