Plumbing originated during ancient civilizations such as the Greek, Roman, Persian, Indian, and Chinese cities as they developed public baths and needed to provide potable water and wastewater removal, for larger numbers of people. Standardized earthen plumbing pipes with broad flanges making use of asphalt for preventing leakages appeared in the urban settlements of the Indus Valley Civilization by 2700 BC. The Romans used lead pipe inscriptions to prevent water theft. The word "plumber" dates from the Roman Empire. The Latin for lead is plumbum. Roman roofs used lead in conduits and drain pipes and some were also covered with lead. Lead was also used for piping and for making baths.
Plumbers, pipefitters, and steamfitters may use many different materials and construction techniques, depending on the type of project. Residential water systems, for example, use copper, steel, and plastic pipe that one or two plumbers can install. Power plant water systems, by contrast, are made of large steel pipes that usually take a crew of pipefitters to install. Some workers install stainless steel pipes on dairy farms and in factories, mainly to prevent contamination.
Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
"We just moved to a new house and Luke did an amazing job installing our home entertainment system. We thought we had a simple TV mounting project, but Luke was able to connect all our equipment (some of which was a bit outdated) so we have one seamless audio/visual system. Plus he was able to fix some errors that Comcast had made and willing to jump in and work on a few other small projects I needed done before the holidays. His price was reasonable and in the week since he performed the work I've had 2 people knowledgeble in contracting or wiring compliment the quality of his work."
Need a quick fix? After having a plumber come out to your house, they might tell you the part needed to fix your toilet or sink issue is going to take a week. Don’t be too amenable if you can’t wait. There’s no shame in working with another plumber who can get the part and do the job when you need it. If you’re doing the job yourself, be sure you know these tips for completing a plumbing fix like a pro.
JJ's Plumbing Repair has no control over, and assumes no responsibility for, the content, privacy policies, or practices of any third party web sites or services. You further acknowledge and agree that JJ's Plumbing Repair shall not be responsible or liable, directly or indirectly, for any damage or loss caused or alleged to be caused by or in connection with use of or reliance on any such content, goods or services available on or through any such web sites or services.
Licensing: There is no standard when it comes to licensing for plumbers. Each state has their own rules and regulations. Most states do require 2-5 years of plumbing experience before the plumbing licensing exam can be taken. Practice tests are available online and can increase the chances of passing the somewhat difficult licensing exam. The plumbers licensing exam will test the knowledge of local codes and best practices.
Abacus’ plumbers are also experts at sewer & pipe repairs, shower & tub repairs/installations, kitchen & bath faucet repair/installations, sink repairs/installation, plumbing inspections, water filtration, water softening, garbage disposal repair/installation, toilet repair/replacement, drain cleaning with drain camera inspections, leak detection/repair, plumbing repair/installation and back flow prevention for all Houston Texas homes & commercial business properties. Need an annual Plumbing Inspection on all your home’s plumbing systems? Ask about the Abacus CLUB. The CLUB membership will give you the peace of mind that your plumbing system is working at top efficiency. Our licensed plumbers will conduct an inspection of your home to look for and fix any potential plumbing problems.
The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
Mr. Rooter® Plumbing is the go-to plumber for homeowners across the country. Why? Our plumbing contractors provide courteous, friendly, affordable, and effective residential plumbing services. We take our mission to exceed our customers’ expectations seriously! From on-time arrivals to licensed and certified plumbing experts, we make sure homeowners are getting the very best plumbing services. You can have total peace of mind and confidence when you call on us! We stand behind our work and go the extra mile to get the job done quickly so you can get back to enjoying your home.
Plumbing is any system that conveys fluids for a wide range of applications. Plumbing uses pipes, valves, plumbing fixtures, tanks, and other apparatuses to convey fluids. Heating and cooling (HVAC), waste removal, and potable water delivery are among the most common uses for plumbing, but it is not limited to these applications. The word derives from the Latin for lead, plumbum, as the first effective pipes used in the Roman era were lead pipes.
Houston’s ever-shifting clay soil puts homes in the greater Houston area at risk from slab leaks. Why? When the concrete slab under your home shifts, the pipes in or underneath the foundation can be damaged, disconnected, or break completely. Fortunately, John Moore plumbers have been working with Houston homeowners since 1965 and have the experience, training and tools to effectively detect and repair slab leaks. Our experienced plumbing team will perform a careful inspection, pinpoint the location, and then provide you with a detailed diagnosis and repair plan to address the leak quickly. For a serious plumbing issues, such as a slab leaks and re-pipes, you can count on our Houston plumbing company, John Moore Services, to treat you and your home with respect and provide you with quality workmanship – guaranteed
Leaky, dripping, rusting faucets can drive you crazy. Is it time to repair, replace or upgrade your faucets? John Moore, the area's trusted master Houston plumbing team since 1965, can examine your fixtures and help you determine whether it can be repaired or if a new faucet is needed. We have a wide variety of replacement parts on hand to resolve most common faucet repairs quickly. If a new fixture is in your future, John Moore carries the latest styles from the industry’s top brands such as Moen, Kholer, and Delta. Have you decided to freshen up your home’s décor with a new look? Are you interested in adding a sprayer to make doing dishes a little quicker and easier? Or perhaps you want a motion sensitive / touch-free kitchen faucet make washing up more sanitary. Whatever your vision or needs may be, purchasing your faucet and installation from John Moore means that you will receive expert installation of a quality fixture that will last for years to come.