Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).
With our highly trained and experienced technicians serving your plumbing, heating, and cooling needs, our workmanship comes with a 100% satisfaction guarantee. We don't send any of our staff members on the front line until we are completely sure that they are qualified for the job. For that reason, they're all drug tested and background checked before joining our team. We also require that they attend ongoing training to stay ahead of the curve with the latest advancements in technology.
Plastic pipe is in wide use for domestic water supply and drain-waste-vent (DWV) pipe. Principal types include: Polyvinyl chloride (PVC) was produced experimentally in the 19th century but did not become practical to manufacture until 1926, when Waldo Semon of BF Goodrich Co. developed a method to plasticize PVC, making it easier to process. PVC pipe began to be manufactured in the 1940s and was in wide use for Drain-Waste-Vent piping during the reconstruction of Germany and Japan following WWII. In the 1950s, plastics manufacturers in Western Europe and Japan began producing acrylonitrile butadiene styrene (ABS) pipe. The method for producing cross-linked polyethylene (PEX) was also developed in the 1950s. Plastic supply pipes have become increasingly common, with a variety of materials and fittings employed.
Sump pumps are used to re-route water away from the lowest point of your home's foundation and protect your basement and easily damaged areas from flooding. In most cases, your sump pump is hardwired to your electrical system or possibly plugged into a wall outlet. Because these power sources can often fail in a storm when water damage occurs, sump pumps are typically equipped with battery backup power.
Master Plumber: To become a master plumber, you must first work for two consistent years as a Journeyman. You must also take an exam and pass both the written and practical portions of it. Once you’ve passed and are a Master Plumber, you can work supervisory roles, and you are also qualified to plan and design entire plumbing systems in addition to your previous skills.
Our failure to enforce any right or provision of these Terms will not be considered a waiver of those rights. If any provision of these Terms is held to be invalid or unenforceable by a court, the remaining provisions of these Terms will remain in effect. These Terms constitute the entire agreement between us regarding our Service, and supersede and replace any prior agreements we might have between us regarding the Service.
One Call Plumbing is a family owned and operated, full service plumbing company. Since 2008, Loren Webster and his team have been showing clients throughout the Durham area what outstanding technical and customer service really looks like. When you work with us, you enjoy the types of benefits that only a local, community based company can offer. Our company stands apart from the others because we:
There’s a reason our slogan is “Serviced Once, Client for Life.” When you call us for plumbing service, you will see why many of our customers are return clients. We strive to provide top-notch customer service from the moment you call to til we solve your plumbing issue, and even after that! Our friendly, knowledgeable staff is always here to answer any questions you may have.
Nationally, the average water heater repair cost ranges between $120 and $200, although prices can range up to $400 or more. Water heater repair costs will depend on the type of water heater you have (tankless, electric, natural gas, etc.), the source of the problem, the cost for new parts, and labor rates in your area. Common water heater issues include problems with the thermocouple, thermostat, heating element and leaks. Most standard electric water heaters have two thermostats and two elements. One example for the cost to replace a bad thermostat is $185 for parts and labor. Replacing both the thermostat and the heating element could cost approximately $150-$200. The thermocouple is a safety device that senses when the pilot light is burning and signals the gas valve to close if the pilot light goes out. If your thermocouple is bad or corroded, the average cost to clean and repair it could be between $350 and $400. If your water heater has started to leak, it is usually more cost-effective to invest in a new water heater than to repair it, unless you’re covered by a warranty.
Get a minimum of three bids. Estimates for an average-sized job should be within a few hundred dollars. Be suspicious of anything that is substantially lower or double the price of the rest, and watch out for hidden fees, like charges for travel expenses. They could be signs of a home improvement scam. A good plumber will not nickel and dime you like this, and many of us will offer free estimates.
Severe plumbing emergencies can cause a lot of collateral damage and result in high costs if not addressed immediately. For example, if your basement floods at 2:00 A.M., it’s vital that an emergency plumber visits right away to resolve the problem and prevent further water damage. Our technicians can arrive at your residence as soon as possible, bringing state-of-the-art equipment to address the plumbing emergency, complete the job in a timely and efficient manner, and get your household plumbing systems back to normal quickly. Providing 24/7 plumbing is just one of the many services Roto Rooter fulfills.
When you have a plumbing issue that needs professional attention, look no further than Handy. No matter how skilled you might be at home maintenance, some jobs should only ever be tackled by a professional, and plumbing is one of them. When you book local plumbers through the Handy platform, you'll be booking a cheap but reliable plumbing professional who will know just where to look to find the source of the problem and who will have all the right tools and expertise to fix it. You'll never go looking for a "local plumbers near me" again!
Bacteria have been shown to live in "premises plumbing systems". The latter refers to the "pipes and fixtures within a building that transport water to taps after it is delivered by the utility". Community water systems have been known for centuries to spread waterborne diseases like typhoid and cholera. However, "opportunistic premises plumbing pathogens" have been recognized only more recently: Legionella pneumophila, discovered in 1976, Mycobacterium avium, and Pseudomonas aeruginosa are the most commonly tracked bacteria, which people with depressed immunity can inhale or ingest and may become infected with. Some of the locations where these opportunistic pathogens can grow include faucets, shower heads, water heaters and along pipe walls. Reasons that favor their growth are "high surface-to-volume ratio, intermittent stagnation, low disinfectant residual, and warming cycles". A high surface-to-volume ratio, i.e. a relatively large surface area allows the bacteria to form a biofilm, which protects them from disinfection.
Not all plumbing companies can guarantee up-front pricing, superior workmanship and parts, licensed and insured plumbing contractors, and courteous support from uniformed professionals. Whether you are in need of drain cleaning or would like to schedule a plumbing inspection for your home, Mr. Rooter's plumbing services can handle it all! Our skilled plumbers are knowledgeable and equipped with the latest tools needed to achieve optimal results. Give us a call at (855) 982-2028, or request a job estimate online.
Specialized plumbing tools include pipe wrenches, flaring pliers, pipe vise, pipe bending machine, pipe cutter, dies, and joining tools such as soldering torches and crimp tools. New tools have been developed to help plumbers fix problems more efficiently. For example, plumbers use video cameras for inspections of hidden leaks or other problems; they also use hydro jets, and high pressure hydraulic pumps connected to steel cables for trench-less sewer line replacement.