The difference between pipes and tubes is simply in the way it is sized. PVC pipe for plumbing applications and galvanized steel pipe for instance, are measured in IPS (iron pipe size). Copper tube, CPVC, PeX and other tubing is measured nominally, which is basically an average diameter. These sizing schemes allow for universal adaptation of transitional fittings. For instance, 1/2" PeX tubing is the same size as 1/2" copper tubing. 1/2" PVC on the other hand is not the same size as 1/2" tubing, and therefore requires either a threaded male or female adapter to connect them. When used in agricultural irrigation, the singular form "pipe" is often used as a plural.[20]
You can beautify your kitchen, too, with our Sink Replacement or Faucet Replacement services, or add to the convenience and health of your water with our Hot Water Dispenser Installation service and Under-Sink Water Filtration Installation service, respectively. With our Garbage Disposal Installation service, you can make your kitchen more functional, as well as more beautiful.
There’s often an Allen wrench that comes with the garbage disposal. I keep it under the sink. When the thing jams, follow the directions in the manual, and I won’t need to come out. Another plumbing tip, don’t believe the myth about putting lemon peels in the disposal to make it smell better. That will just make it jam faster.  These are the things you should never pour down the drain.
Even attempting to fix your plumbing repairs on your own without proper knowledge can cause massive problems down the line. Book your local plumber using the Handy platform and you’ll be matched with plumbers near you who know just what they’re doing. Experienced and practiced in their craft, they’ll provide you with the best job at a price that won’t break the bank. When you use Handy to find cheap plumbers near me, you can rest assured that you’ll be connected with a capable plumbing service who will get your job done without you having to worry about how much a plumber costs ever again.
Master Plumber: To become a master plumber, you must first work for two consistent years as a Journeyman. You must also take an exam and pass both the written and practical portions of it. Once you’ve passed and are a Master Plumber, you can work supervisory roles, and you are also qualified to plan and design entire plumbing systems in addition to your previous skills.
When you book an affordable plumber, whether it's to fix a broken boiler or to unclog a drain, you want to know they're skilled enough for the task at hand. Nothing is worse than sending an amateur with a wrench to look at your pipes. Odds are, there will be more damage than when they started. All plumbers on the Handy platform are vetted, verified, and background checked way before they arrive at your home, so you can be sure that they're the right person for the job. 

Most plumbers, pipefitters, and steamfitters learn their trade through a 4- or 5-year apprenticeship. Apprentices typically receive 2,000 hours of paid on-the-job training, as well as some classroom instruction, each year. In the classroom, apprentices learn safety, local plumbing codes and regulations, and blueprint reading. They also study mathematics, applied physics, and chemistry. Apprenticeship programs are offered by unions and businesses. Although most workers enter apprenticeships directly, some start out as helpers. The Home Builders Institute offers a pre-apprenticeship training program in plumbing and other trades.
Nationally, the average water heater repair cost ranges between $120 and $200, although prices can range up to $400 or more. Water heater repair costs will depend on the type of water heater you have (tankless, electric, natural gas, etc.), the source of the problem, the cost for new parts, and labor rates in your area. Common water heater issues include problems with the thermocouple, thermostat, heating element and leaks. Most standard electric water heaters have two thermostats and two elements. One example for the cost to replace a bad thermostat is $185 for parts and labor. Replacing both the thermostat and the heating element could cost approximately $150-$200. The thermocouple is a safety device that senses when the pilot light is burning and signals the gas valve to close if the pilot light goes out. If your thermocouple is bad or corroded, the average cost to clean and repair it could be between $350 and $400. If your water heater has started to leak, it is usually more cost-effective to invest in a new water heater than to repair it, unless you’re covered by a warranty.
Licensing: There is no standard when it comes to licensing for plumbers. Each state has their own rules and regulations. Most states do require 2-5 years of plumbing experience before the plumbing licensing exam can be taken. Practice tests are available online and can increase the chances of passing the somewhat difficult licensing exam. The plumbers licensing exam will test the knowledge of local codes and best practices.
My plumbing experience was  to have the plumbing  disconnected under the sink so the counter top and new sink could be installed.  I thought the service  of $115 was high, but usually if there is an additional fees, it is usually rolled into the cost of repairs or labor.  This company also charged 3.75 % for putting it on a credit card, which was not mentioned until I received the invoice in the mail after paying on the phone.
Our master plumbers in Houston will assess the age and integrity of your pipes and determine the best course of action. Whether your home plumbing requires a pipe replacement, a horizontal pipe replacement for the pipes in your attic, or a whole-home repipe with highly durable and flexible PEX piping, you can rest easy knowing that your home is in the experienced hands of the licensed and highly-qualified John Moore Houston plumbing team.

Leaky, dripping, rusting faucets can drive you crazy. Is it time to repair, replace or upgrade your faucets? John Moore, the area's trusted master Houston plumbing team since 1965, can examine your fixtures and help you determine whether it can be repaired or if a new faucet is needed. We have a wide variety of replacement parts on hand to resolve most common faucet repairs quickly. If a new fixture is in your future, John Moore carries the latest styles from the industry’s top brands such as Moen, Kholer, and Delta. Have you decided to freshen up your home’s décor with a new look? Are you interested in adding a sprayer to make doing dishes a little quicker and easier? Or perhaps you want a motion sensitive / touch-free kitchen faucet make washing up more sanitary. Whatever your vision or needs may be, purchasing your faucet and installation from John Moore means that you will receive expert installation of a quality fixture that will last for years to come.
You can depend on Spengler to provide unmatched emergency plumber service and guaranteed satisfaction for your home and business plumbing needs. Our up-front prices, professionalism and friendly on-time service have helped us become the preferred choice for thousands of homes and businesses across the Metro East area including our immediate local area O’Fallon, Belleville, Fairview Heights, Shiloh, and Swansea. Other areas include Collinsville, Edwardsville, Alton, Highland, Granite City, and surrounding Illinois communities. Rooter plumbers in Belleville, IL provide plumbing maintenance including toilet repairs and clogged drain cleaning. Rooter’s and plumbers offer residential  plumbing services that clients depend on for all of their local plumbing needs.
We offer several financing options for new equipment, as well as our Priority Club Membership that grants members exclusive discounts, priority service, annual tune-ups, and much more. Plus, we make it our mission to give back to the community that’s continually supported us for decades. Our team members regularly donate their time, money, and efforts to numerous charitable organizations, fundraising endeavors, and worthwhile causes throughout the Northern Virginia and suburban Maryland area.
×